Cable extender 1-wire, 2m

This is an extension cord for 1-wire sensors. It allows to lengthen a loop of a 1-wire sensor and plug 2 1-wire sensors to the same extension cord.

• A cable with RJ12 jacks on its ends;
  
• 1-wire splitter included;
• Flat 6-wire cable, AWG24

The Active Extender-Splitter for Connecting 1-wire Sensors to the NetPing Devices

• 5 ports for connecting 1-wire sensors;
• The total length of all the wires for all 1W R912R2 ports to all connected sensors - up to 5*50 = 250 meters;
• Maximum distance from the host (considering the total length of the wires on the 1-wire port to the sensors and R912R2) - no more than 50 meters;
• It is prohibited to cascade R912R2;
• A compact plastic case with a hole for mounting;
• The power is from the host device.

This sensor is designed to monitor the the quality of power in the outlet. The sensor must be connected to the RJ-12 (6P6C) connector of the NetPing device.

• The measuring range of the main voltage current value is 70 ... 276 V ± 4%, RMS measurement (when measuring a sinusoidal alternating voltage close to the nominal frequency without distortion and harmonics);
• Measurement of alternating current frequency is 50/60 Hz ± 2%;
• Frequency measurement period and RMS - 6s;
• Monitoring of short-term dips and overvoltages in the power supply network;
• Sensor power from the host device - 5 V, current up to 20 mA;
• A compact plastic case;
• Operating temperature range is -30°С ... +50°С (without moisture condensation, at normal humidity).

A device of power supply sockets remote management via Ethernet/Internet network (IP power distribution unit) with SMS management support.

• 4 controllable sockets (IEC320-C13);
• 2 x 10/100-BASE-TX Ethernet ports;
• A built-in 3G GSM modem for SMS management and notification;
• Built-in ionistor for the operation of the warning system in the absence of 220 V;
• Ability to connect the battery module;
• A metal body for installing into a 10' rack 1U or mounting on a flat surface;
• External 1-wire sensors can be connected: temperature, humidity, supply voltage, analog sensor adapter;
• 6 I/O lines for connecting external sensors of "dry contact" type;
• Operating temperature range: -30...50 °C (no condensation, normal humidity).

A device of power supply sockets remote management via Ethernet/Internet network (IP power distribution unit) with SMS management support.

• 4 controllable sockets (JT-G45-120-4P, “Schuko” sockets, Type F);
• 2 x 10/100-BASE-TX Ethernet ports;
• A built-in 3G GSM modem for SMS management and notification;
• Built-in ionistor for the operation of the warning system in the absence of 220 V;
• Ability to connect the battery module;
• A metal body for installing into a 10' rack 1U or mounting on a flat surface;
• External 1-wire sensors can be connected: temperature, humidity, supply voltage, analog sensor adapter;
• 6 I/O lines for connecting external sensors of "dry contact" type;
• Operating temperature range: -30...50 °C (no condensation, normal humidity).
  

A device of power supply sockets remote management via Ethernet/Internet network (IP power distribution unit).

• 4 controllable sockets (JT-G45-120-4P, “Schuko” sockets, Type F);
• 2 x 10/100- BASE-TX Ethernet ports;
• A metal body for installing into a 10' rack 1U or mounting on a flat surface;
• External 1-wire sensors can be connected: temperature, humidity, supply voltage, analog sensor adapter;
• 6 I/O lines for connecting external sensors of "dry contact" type;
• Operating temperature range: -30...50 °C (no condensation, normal humidity).

The adapter is designed to connect analog sensors and is able to measure the flowing current, voltage and resistance.

• The range of voltage measurement 0..30 VDC ± 3%;
• The range of current measurement -30..30 mA ± 3%;
• The range of resistance measurement 0..29999 Ohm ± 3%;
• The power supply of the current loop: 12V 100 mA, 24V 30 mA;
• Powered from the host device;
• Connection interface: 1-wire;
• Operating temperature range: -30 C to + 50 C (without moisture condensation, normal air humidity).

This is a device for remote sensor monitoring via the Ethernet/Internet on a DIN rail. It allows you to receive information about the status of sensors and notifications about triggering of sensors, to control connected devices remotely.

• A compact case for mounting on a DIN rail;
• 1-wire sensors support;
• 16 Input and 4 Output lines for connecting external sensors and controlling external devices;
• 4 built-in low voltage relays;
• RS-232/485 port (TCP-COM);
• Support for external sensors: temperature sensors, humidity sensors, door metal sensors, liquid sensors, smoke detectors, supply voltage sensors and so on;
• 2 х 10/100-BASE-TX Ethernet ports;
• Power supply of the device using a 12V 2A power supply unit or an external module for NetPing 85M2 batteries.

This device is for remote monitoring of sensors via the Ethernet/Internet network. It allows you to control external devices and receive information about the conditions of sensors and notifications about a sensor status remotely.

• 2 х 10/100-BASE-TX Ethernet ports;
• A metal case with brackets for mounting on a DIN rail;
• 4 built-in 24 V changeover relays with an indication for switching;
• A built-in temperature sensor;
• 1-wire sensor support;
• 4 Input lines for connecting sensors of a “dry contact” type;
  
• External sensors are supported: temperature, humidity, door metal, liquid, voltage supply, motion and so on;
• Power of the device from POE (Power over Ethernet) or using a 12V 2А power battery.

This device is for remote monitoring of sensors via the Ethernet/Internet network. It allows receiving information about the status of sensors and notifications about sensor triggering remotely.

• A metal case for mounting on a 19' 1U rack;
• 1-Wire sensors support;
• 12 IO lines for connecting external sensors and controlling external devices;
• An analog input 0–30 mA, 0–30 V, 0–30 kOhm;
• Two built-in low voltage relays;
• Built-in GSM3G modem;
  
• 2 х 10/100-BASE-TX Ethernet ports.

This device is for remote monitoring of sensors via the Ethernet/Internet network. It allows receiving information about the status of sensors and notifications about sensor triggering remotely.

• A metal case for mounting on a 19' 1U rack;
• 1-Wire sensors support;
• 12 IO lines for connecting external sensors and controlling external devices;
• An analog input 0–30 mA, 0–30 V, 0–30 kOhm;
• Two built-in low voltage relays;
• 1 х 10/100-BASE-TX Ethernet port.

This device is for remote monitoring of sensors via the Ethernet/Internet network. It allows receiving information about the status of sensors and notifications about sensor triggering remotely.

• A metal case for mounting on a 19' 1U rack;
• 1-Wire sensors support;
• 12 IO lines for connecting external sensors and controlling external devices;
• An analog input 0–30 mA, 0–30 V, 0–30 kOhm;
• Two built-in low voltage relays;
• Built-in GSM3G modem;
  
• 1 х 10/100-BASE-TX Ethernet port.

A device of power supply sockets remote management via Ethernet/Internet network (Switched Metered ATS IP PDU) with SMS management support.

• 8 controllable 100V ... 240V AC, 50/60 Hz sockets;
  
• 2 independent power supply inputs (automatic and switching between the inputs by a command);
• 2 x 10/100-BASE-TX Ethernet ports;
• A built-in 3G GSM modem for SMS management and notification;
• A metal body for installing into a 19' rack 1U;
• External sensors can be connected: temperature, humidity, door, leakage, supply voltage and other

A device of power supply sockets remote management via Ethernet/Internet network (Switched Metered ATS IP PDU) with SMS management support.

• 8 controllable 100V ... 240V AC, 50/60 Hz sockets;
• 2 independent power supply inputs (automatic transfer switch);
• 1 x 10/100-BASE-TX Ethernet ports;
• A built-in 3G GSM modem for SMS management and notification;
• A metal body for installing into a 19' rack 1U;
• External sensors can be connected: temperature, humidity, door, leakage, supply voltage and other.

IR controller for remote and automatic control of devices with infrared interface via Ethernet (web, SNMP, HTTP API).

• Learned from the original remote control, stores and plays back up to 32 IR commands;
• Compact aluminum hanger housing with hinge;
• Supports 1-wire sensors;
• Supports two dry contact sensors with the ability to connect 2 control buttons;
• 2 x 10/100-BASE-TX Ethernet ports with POE broadcasting;
• Possibility of simultaneous power supply of the device from power supply and POE.