SENSORS AND ACCESSORIES

Sensitive cable for use in conjunction with the VT592 sensor. It can be mounted in hard-to-reach places and cover large areas compared to point sensors.

• The leak cable is 10 m long;
• Operating temperature up to 70 °C;
• Operating humidity up to 95%, non-condensing;
• The cable dries within 15 seconds after the end of contact with water;
• Tensile strength — 72 kg;
• The weight of the cable is 500 g per meter;
• Diameter — 6 mm;
• Leak-sensitive cores — 30AWG with a conductive fluoropolymer shell.

The Active Extender-Splitter for Connecting 1-wire Sensors to the NetPing Devices

• 5 ports for connecting 1-wire sensors;
• The total length of all the wires for all 1W R912R2 ports to all connected sensors - up to 5*50 = 250 meters;
• Maximum distance from the host (considering the total length of the wires on the 1-wire port to the sensors and R912R2) - no more than 50 meters;
• It is prohibited to cascade R912R2;
• A compact plastic case with a hole for mounting;
• The power is from the host device.

The adapter is designed to connect analog sensors and is able to measure the flowing current, voltage and resistance.

• The range of voltage measurement 0..30 VDC ± 3%;
• The range of current measurement -30..30 mA ± 3%;
• The range of resistance measurement 0..29999 Ohm ± 3%;
• The power supply of the current loop: 12V 100 mA, 24V 30 mA;
• Powered from the host device;
• Connection interface: 1-wire;
• Operating temperature range: -30 C to + 50 C (without moisture condensation, normal air humidity).

The device does not work independently, it can function only with a NetPing host device.

• A number of output sockets 8 pcs ("computer" type C13 R-30SN);
• 2 buttons to disconnect the sockets temporary, are programmed via the web interface of a host device;
• Total output power: 3,5 kW;
• Power to a channel: 1,5 kW;
• Operating voltage range: 190...220 V / 50–60 Hz;
• Short circuit protection: built-in fuse;
• Host connection interface: 1-wire;
• Metal case to build in a rack 19' 1U;
• Operation temperature range: -30 °С ... +50 °С (without moisture condensation, normal air humidity).

The device does not work independently, it can function only with a NetPing host device.

• A number of output sockets 7 pcs.;
• 2 buttons to disconnect the sockets temporary, are programmed via the web interface of a host device;
• Total output power: 3,5 kW;
• Power to a channel: 1,5 kW;
• Operating voltage range: 190...220 V / 50–60 Hz;
• Short circuit protection: built-in fuse;
• Host connection interface: 1-wire;
• Metal case to build in a rack 19' 1U;
• Operation temperature range: -30 °С ... +50 °С (without moisture condensation, normal air humidity).

NetPing Light Sensor 813S2 is a compact luminous flux presence sensor designed to connect with NetPing devices.

• Threshold adjustment 10–7000 Lx;
• An adjustment step 10–300 Lx;
• A viewing angle 25–30°;
• Hysteresis 20%;
• Sensor triggering/release time from 1 s up to 20 s;
• An output type NPN, an open drain/dry contact connected to an IO-line of a NetPing device;
• An operating temperature range -30...+50°С without moisture condensation.

This sensor is designed to monitor the the quality of power in the outlet. The sensor must be connected to the RJ-12 (6P6C) connector of the NetPing device.

• The measuring range of the main voltage current value is 70 ... 276 V ± 4%, RMS measurement (when measuring a sinusoidal alternating voltage close to the nominal frequency without distortion and harmonics);
• Measurement of alternating current frequency is 50/60 Hz ± 2%;
• Frequency measurement period and RMS - 6s;
• Monitoring of short-term dips and overvoltages in the power supply network;
• Sensor power from the host device - 5 V, current up to 20 mA;
• A compact plastic case;
• Operating temperature range is -30°С ... +50°С (without moisture condensation, at normal humidity).

The shock sensor allows registering shocks and vibration as well as loud bangs and acoustic shocks of the surface on which it has been installed. It is normally used to report vandalism at remote sites and equipment boxes.

• Connected to the IO-lines of NetPing devices;
• Independent two-level adjustment of the shock force;
• A patented piezo-spring element;
• High stability and reliability of its operation;
• The plastic case has a device for attaching the sensor to any surface;
• Contact conditions: N.O. contact (normally opened contacts);
• Sensor supply voltage +12 V, ± 20%;
• 6 I/O lines for connecting external sensors of "dry contact" type;
• Length of the wire 1 m.

A temperature sensor -55°C ... +125°C with a 1-wire interface. A cable length is 2 meters. For NetPing server room environmental monitoring solutions and power distribution units.

• A sealed body, bears an immersion in a liquid;
  
• A range of operating temperatures is -55°C ... +125°C;
• An accuracy is ±0,5°C in a range -10°C ... +85°C;
• An embedded unique sensor number;
• An inseparable cable 2 meters long

VT592 cable leak sensor is designed to work in conjunction with the WLC10 leak cable. The ability to connect the sensor to the IO line makes it easy to integrate it into almost any system built on NetPing power monitoring and management devices.

• Operating temperature range: -10°C ... 100 °C;
• Operating humidity range: 10% ... 90% (non-condensing);
• Triggering time: up to 15 seconds;
• A compact plastic case with a hole for mounting;
• Sensor of the "dry contact" type;
• A power supply of a sensor is 5V.

A relative humidity sensor with a 1-wire interface and a built-in temperature sensor. For NetPing server room environmental monitoring solutions and power distribution units.

• A plastic body with cuts;
  
• A single-chip sensor HIH-4000;
• Operating temperature range is -40С ... +85С;
  
• Accuracy of measurement of humidity ±8% in the range of 60%...100% at a temperature of 25°C;
• Accuracy of measurement of humidity ±5% in the range of 25%...60% at a temperature of 25°C;
  
• Accuracy of temperature measurement ±2°C;
  
• An embedded unique sensor number;
  
• An inseparable cable 2m long.

A temperature sensor I²C for measuring an ambient air temperature indoors from -40°C to +125°C. Avoid water contacting a temperature sensor! For NetPing power distribution units.

• Plastic body with slots;
  
• Must be installed indoors with no possibility to contact water;
• Based at a digital single-chip thermometer TCN75A;
• Operating temperature range is -40°C ... +125°C;
• Accuracy is ±1,5°C in the range -40°C ... +125°C;
• Digital bus of the I²C standard;
• Possibility to set a sensor address independently;
• Nondetachable wire 2 meters long

A relative humidity sensor for measuring relative humidity in % and a built-in temperature sensor. For NetPing power distribution units.

• Plastic cover with slots;
  
• Sensor is constructed based on the chip HIH6031-021;
• Humidity measuring range is 0% ... 100%
• Operating temperature range is 40°C ... +100°C;
• Humidity measuring accuracy is ±4,5%;
• Temperature measuring accuracy is ±1°C;
• Nondetachable wire 2 meters long

A smoke detector is designed to reveal a fire indoors, that is accompanied by a smoke. It can be plugged to NetPing server room environmental monitoring solutions.

• Dome construction of a body to be mounted on a ceiling;
  
• 2-wire flat cable through which a power supply of a sensor is provided;
• Information about triggering by changing internal resistance of a sensor

A sensor allows detecting the power voltage in the power outlet.

• it is manufactured in the case of the power unit with the IEC320 C7 (IP20) socket. It can be plugged into any outlet using a detachable power cord.

• has the internal nodes powered from the grid and thus may maintain operation in the range between AC 70...250 V with the frequency of 50/60 Hz.

• Triggering threshold: 178–193 V.

• Releasing threshold: 155–175 V.

• The output type is «dry contact» / normally closed and normally opened contacts (built-in relay).

• Loop is 1,5 meter long.

A door position sensor. The sensor is designed to be mounted on a metal door of a cabinet or a server room. It contains reed contacts ("dry contact"). For NetPing server room environmental monitoring solutions and power distribution units.

• Reed contacts of the sensor close when a magnet approaches;
  
• The sensor is to be mounted on a door of a server room or a cabinet with equipment;
• It is a patch sensor, designed to be mounted on metal surfaces

A leakage sensor allows to define a presence of water in the spot where a sensor is installed. For NetPing server room environmental monitoring solutions and power distribution units.

• It is mounted several millimeters above the floor in the place of possible water accumulation;
  
• Output type "dry contact";
• Power supply voltage of a sensor is 5V

A motion sensor is designed to register movement. Allows to register any movement in a 10 meters area. It is connected to NetPing server room environmental monitoring solutions.

• It is insensible for animals weighing up to 27 kilogram;
  
• Detection area: 10 meters;
• A power supply of a sensor is 9V ... 16V DC

The air flow sensor allows you to monitor the presence or absence of air pressure. It contains reed contacts ("dry contact"). It is connects to the IO line of a NetPing device.

• For cupboards heated by fan heaters;
  
• For remote control of the fan operation at any point of an object, air flow control: yes, no;
  
• The mechanical principle of operation;
  
• Universal application;
  
• Small size;
  
• A plastic case;
  
• The status of contacts: N.Z. (normally closed or closed);
  
• One-piece wire of 0.5 m long.
  

A siren alarm is designed to be plugged to NetPing server room environmental monitoring solutions. The siren allows to sound alert by a command from the interface of a NetPing device.

• 12V powered by a NetPing device;
  
• Loudness level is 105 dB

An IR module for devices remote control via TCP/IP network (web, SNMP, HTTP API) and SMS-commands with an IR interface (for example, remote control for air conditioner). It is not an independent device and it must be connected to a basic NetPing server room environmental monitoring solutions and power distribution units!

• Is trained from an original remote control;
  
• Reproduces up to 16 IR commands, saved in a memory of a module;
• Cable length to a basic device is up to 10 meters;
• A body of a device is in a form of a dome camera

A controllable socket allows to turn on/turn off and restart power supply of 100V ... 240V AC, 50/60 Hz external load, with a current up to 10A. A socket has to be plugged into an IO line of a basic NetPing server room environmental monitoring solutions and power distribution units!

• Switching capacity up to 2 KW;
  
• Management from IO line of NetPing device;
• A possibility to be installed on DIN rail;
• A socket to plug a Euro plug

An adapter for NetPing power distribution units (PDU). A special cable-adapter for connecting a euro plug from a computer socket to a usual power outlet in a body of a NetPing PDUs.

• C14 plug on a cable;
  
• Euro plug (F type) on a cable;
• Up to 16A 110V ... 230V AC, 50/60 Hz

An universal adapter is designed to connect a power supply euro plug of a NetPing power distribution units (PDU) to a UPS socket (UPS, C13). In addition, an adapter can be used to plug a NetPing PDUs euro plug to a UPS socket (UPS, C13). A grounding contact of the adapter can be used with only a plug that has a pin as a grounding contact.

• Up to 16A 110V ... 230V 50/60Hz;
  
• Universal contacts to connect any plug;
• Can be plugged into a C13 socket (UPS)

A power adapter with an output voltage of 48V is designed to feed POE injectors, for example NP-SM4.

• Output voltage 48V DC;
  
• Output current 1.5A;
• Input voltage 100V ... 240V AC, 50/60 Hz;
• Output socket type DJK11 for a 2.1 mm pin;
• Power supply plug a euro plug

This is an extension cord for 1-wire sensors. It allows to lengthen a loop of a 1-wire sensor and plug 2 1-wire sensors to the same extension cord.

• A cable with RJ12 jacks on its ends;
  
• 1-wire splitter included;
• Flat 6-wire cable, AWG24

This is an extension cord for 1-wire sensors. It allows to lengthen a loop of a 1-wire sensor and plug 2 1-wire sensors to the same extension cord.

• A cable with RJ12 jacks on its ends;
  
• 1-wire splitter included;
• Flat 6-wire cable, AWG24

This is an extension cord for 1-wire sensors. It allows to lengthen a loop of a 1-wire sensor and plug 2 1-wire sensors to the same extension cord.

• A cable with RJ12 jacks on its ends;
  
• 1-wire splitter included;
• Flat 6-wire cable, AWG24

It allows to extend the length of a cord loop for 4 meters. Cable extender can be sequentially plugged in each other to achieve a necessary length of a sensor cord loop.

• Cable length 4 meters;
  
• Flat 4-wire cable

This is a power adapter, which can be used to feed NetPing server room environmental monitoring solutions.

• Output voltage 12V DC;
• Output current 0.5A;
  
• Input voltage 100V ... 240V AC, 50/60 Hz;
• Type of output jack DJK-02A for 2.1 mm pin "+" power in the center